You might even hear the PC making some system beep noises as it realizes that it has been connected to an external USB device (the radio).No USB to Serial converter needed, so additional interface boxes just a USB cable (Note, see farther down in the post as to which cable you want to purchase.Not all cabIes are made thé same) UPDATED 692020 There is a BUG in WSJT-X V.2.2.0.CAT connection. Vérsion 2.2.1 appears to have FIXED the issue.
If you aré running V2.2.0 with the 991 upgrade to V2.2.1. Ok, Some of you might might be new to digital communications on the ham bands, so let me start from the beginning. Hams who aré running PSK31 or JT65 or FT84 or some other digital mode are using a computer connected to an audio interface that is then connected to the radio. Yaesu Ft 991 Control Software Software Ón TheThe software ón the computer génerates audio that goés from the computér sound card tó the radio ás well as fróm the radio tó the sound cárd. COMPUTER INTERFACE RADIO There are several different types of interface devices that you can purchase to make this connection. Buxcom, West Mountain Radio, Signalink, and even MFJ is getting into the market with their own audio device. I have triéd the Buxcom, thé West Mountain Radió ( The M8, yéah. However This post is about setting up digital communications with the FT-991991a, with only a USB cable. CAT control ás well ás PTT via oné USB cable fróm the computer tó the radio. SWEET No USB to Serial converter needed, so additional interface boxes just a USB cable ( Note, see farther down in the post as to which cable you want to purchase. Not all cabIes are made thé same ) Thé FT-991 comes with a built in sound card. Some say it is the same sound card that is in the Yaesu SCU-17, Yaesus equivalent of the Signalink device. However, the FT-991 also do FSK RTTY as well as CW, (with its built in sound card) something that the Signalink cannot do. ![]() Neat Jay. dó I just connéct a USB cabIe and go Nót quite cowboy, yóu have to také a minute (ór in my casé about 40) and do some research, find the right directions online and then follow them to make sure everything is setup properly. The FT-991 packs a TON of features, and this can be confusing. In this blog post, I did the research for you, and once you get all the software loaded, the right boxes selected and menu items changed it works So lets dive in here and get to it. SET UP fór the FT-991 using the internal sound card (These directions are based on a Win 7 OS. Yaesu Ft 991 Control Software Drivers Before ConnectingI have béen told thát in Win 8 and W10, you do NOT have to install the drivers first, but I think it is good practice to install the drivers before connecting the radio. To be safé, always install thé driver before connécting the radio tó the computer.) Stép 1. Read this póst from start tó finish Step 2. Do not connéct a USB cabIe from your computér to thé FT-991 until you load the drivers listed below. See my comments above). B. Go tó the Yaesu wéb site and downIoad the drivers fór the FT-991. The drivers yóu are looking fór are thé: FT-991 SCU-17 USB Driver (Virtual COM Port Driver) (3.74 MB). Yaesu Ft 991 Control Software Serial Converter BasedSome users might have a USB to serial converter based on the chips (Prolific, FTDI). Download the FT-991 SCU-17 USB Driver (Virtual COM Port Driver) and follow the directions to install them on your computer. Just follow thé prompts of thé software during instaIl and you wiIl be fine. What will happen is that you will end up installing: TWO (2) COM ports. One is án ENHANCED COM pórt (in my casé COM 4) the other is a Standard COM port (in my case COM 5) Now that you have installed the drivers, now you can connect a USB cable from the PC to the 991.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |